Description Ramset™ Epcon G5 is a high performance chemical epoxy adhesive specially formulated for hot or warm weather. Due to its fast curing property, you don’t have to waste your valuable time waiting for longer cure times or waste money disposing of dried up nozzles. With an extended working time (15 minutes) and a full cure in less than 2 hours, your crew can keep working more efficiently, not waiting, saving you time and money. The epoxy resin and hardener are thoroughly and evenly mixed as they are dispensed from the dual cartridge through a static mixing nozzle, directly into the anchor hole. It is ideally used in tropical climate and it works well in dry, damp, wet and flooded holes. Advantages • High Performance Epoxy: Shallower embedment depth required hence saving on materials • Fire Resistant Structures: Tested up to 4 hours FRP with standardized fire curve (ISO 834) • Fast Cure Formula: 2-hour cure time at 20°C for same day loading of anchors • Cost savings: Less delay of work, less materials used, less nozzles used • High Strength Non Shrink: Suitable for cored and oversized holes • VOC Compliant: Virtually odorless, can be used indoors. LEED tested. Styrene free • Water Insensitivity: Works in wet, flooded holes and under water applications. • Approved for cracked, uncracked and seismic zones. read more

CHOCKFAST ORANGE (PR-610TCF) is a specially formulated 100% solids, two component inert filled casting compound developed for use as a chocking or grouting material. CHOCKFAST is designed to withstand severe marine and industrial environments involving a high degree of both physical and thermal shock. The compound is non-shrinking and has very high impact and compressive strength. Years of successful in-service experience have shown the use of PR-610TCF to be a far superior yet less expensive method of establishing and permanently retaining precise equipment alignment under extreme conditions. PR-610TCF is approved or accepted for its intended marine use by American Bureau of Shipping, Lloyd's Register, Bureau Veritas, Det Norske Veritas, Germanischer Lloyd and most other major regulatory agencies worldwide read more

    Resin-free: Yes Min. temperature conditions: -10 °C Max. temperature conditions: 140 °C Kinematic oil basis viscosity: 16.5 mm²/s Conditions for viscosity of oil basis: at 40°C Min. flashing point of active ingredient: 200 °C Silicone-free: Yes Acid-free: Yes AOX-free: Yes High capillary activity Optimum creeping properties for excellent rust penetration, i.e. even stubborn, rusted-on screw connections are loosened   *Optimum rust removal Penetrates rust and loosens seized up screws and bolts   *Excellent water displacement Displaces and penetrates moisture, e.g. in the case of contact difficulties   *Corrosion-protection additives for optimum corrosion protection Provides lasting protection against further corrosion   *Resin-free and acid-free *Silicone-free *Compatible with rubber and seals   High capillary activity Optimum creeping properties for excellent rust penetration, i.e. even stubborn, rusted-on screw connections are loosened   Optimum rust removal Penetrates rust and loosens seized up screws and bolts   Excellent water displacement Displaces and penetrates moisture, e.g. in the case of contact difficulties   Corrosion-protection additives for optimum corrosion protection Provides lasting protection against further corrosion   Resin-free and acid-free   Silicone-free   Compatible with rubber and seals read more

GENERAL DESCRIPTION: Weld-On® 717™ is a clear or gray, low VOC emission, heavy bodied, medium setting, high strength PVC solvent cement for all classes and schedules of pipe and fittings, including Schedule 80, with interference fit through 12 inch (315 mm) diameter. It has good gap filling properties and is recommended for solvent welding joints where a sizable gap exists between pipe and fitting – e.g. large pipe sizes – and when more working time is required in warm weather. APPLICATION: WELD-ON 717 is for use on all types of PVC plastic pipe applications, Type I and Type II. It is suitable for use with potable water pressure systems, irrigation, turf, conduit, industrial pipe applications, sewer, drain, waste and vent systems. read more

The #1 selling, biodegradable, waterless, petroleum solvent-free hand cleaner that contains no harsh chemicals, petroleum solvents or ammonia that can sting cuts or abrasions. Pure, fresh-smelling natural citrus power does the cleaning. Fortified with aloe, lanolin, glycerin, and other skin conditioners to soothe raw, rough hands. Fine Pumice deep cleans the toughest dirt. Works great on laundry stains (smooth lotion only), scuff marks, tile floors, pet odors and many other household cleaning needs. Automobile Suggested Applications: Resins, oil, grease, tar, grime, soil, printers’ ink, epoxies, paint, rubber cement, gasket and tile cements DIRECTIONS FOR USE: Rub hand cleaner into dry hands (use no water) until dirt or grease is dissolved. Wipe dry or rinse with water.   read more

Extends belt life. Penetrates the cord fibers of “V” belts to restore pliability and flexibility. Prevents belt slippage due to heat, cold, dampness, dust and glazing. Eliminates squeaking and slipping Automobile Suggested Applications: Fan belts, water pumps, power steering, sewing machines, washing machines, air conditioners, lawn mowers and power tools   DIRECTIONS: Shake well. Attach extension tube. While engine is running, spray lightly on inner working surface of belt near smallest or upper most pulley. Allow belt to run for several minutes to condition and cure dressing. Reapply as needed. Do not spray on pulleys.   read more

Nabakem Mega Check Dye Penetrant DPI    1 unit : 450ml     Cleaner Developer Penetrant    • Special equipment not required. Easy-to-use. • This product changes invisible fine cracks into visible red-colored cracks, enabling you to check all cracks. • Safe for aluminum alloy and magnesium alloy subject to easy corrosion. • Inspection results are maintained unless you clean them.   read more

The universal conformal coating for printed circuit boards. A fast drying, transparent, acrylic coating, with good dielectric properties. It shields printed circuit boards or other parts from corrosive (atmospheric) influences. This film protects printed circuit boards from leakage currents and short circuits.   Features: + Provides a protective and insulating film against atmospheric influences such as moisture, oxidation, dust or corrosive vapours. + Good adhesion on metal, plastic, wood, glass, ... + The film is resistant to diluted acids, alkalines and atmospheric attack. + Can be soldered through. + Prevents sparking and corona effects. + Remains transparent and flexible even after a long period. + Temperature range: -40°C to +60°C. read more

read more

The consistency of Falk LTG changes with operating conditions. As manufactured it is a National Lubricating Grease Institute (NLGI) #1 grade. Working of the lubricant under actual service conditions causes it to become semifluid while the grease near the seals will set to a heavier grade, helping to prevent leakage. Falk LTG is highly resistant to separation, easily outperforming all other lubricants tested. The resistance to separation allows the lubricant to be used for relatively long periods of time. Compatibility Falk LTG is compatible with most coupling lubricants. For optimum performance it is recommended that couplings be cleaned of old grease before packing with Falk LTG. read more